Proud to support Glaucoma UK for 2024.
Resutile is a high performance, two-pack polyurethane floor coating which is designed to provide excellent chemical resistance and light fastness. It is a hard-wearing and tough but flexible coating with very good resistance to impact, abrasion and high temperature. Resutile is regularly used in the aviation industry due to its excellent resistance to Skydrol.
New concrete must be clean, sound, dry and fully cured and surface laitance removed by vacuum enclosed shot blasting or mechanical grinding, a minimum strength of 25N/mm2 is required.
Must be clean, sound, dry. Old clear varnish/topcoat must be removed/sanded prior to application, as it may affect the inter-coat adhesion with Resutile.
Remove all dirt, oil, grease, old paints or any or other surface contaminants by vacuum enclosed shot blasting, scarifying or mechanical grinding. Fats, oils or greases must be removed by mechanical means and detergent washing. Local repairs should be carried out using Resuscreed PA or Resuscreed 45.
All previous coatings and loose floor paints must be removed by mechanical preparation as described in the above section and primed as specified. if the old resin flooring cannot be removed, then please consult with our technical team for advice on inter-coat adhesion and suitability, as it may not be compatible with existing floor coating.
Where Resutile is applied to masonry/concrete surfaces, care must be taken to ensure that surface preparation is thorough but does not disfigure the surface.
Where surfaces are found to be porous a primer coat may be required to achieve a uniform sealed surface.
Resutile may be applied directly to concrete or as a seal coat or topcoat to a resin floor system specified in our datasheets where a primer is not required.
When applied directly to porous substrates the surface may require priming. Dry surfaces may be primed with Resuseal WB Clear or Resuprime ST.
Where the Relative Humidity of the substrate exceeds 75% Resuprime MVT should be specified and selected on the basis of hygrometer readings in
accordance with BS 8203. The number of coats to be applied is chosen in accordance with the following table.
ERH% Required Coating Thickness
75-85 1coat of RESUPRIME MVT at 200 microns per coat
85-92 2coats of RESUPRIME MVT at 200 microns per coat
92-97 3coats of RESUPRIME MVT at 200 microns per coat
The ambient temperatures of the area should not be allowed to fall below 10°c throughout application and curing. The surface temperature must be above 5°c.
Mixing: Pre-mix the base component to a uniform consistency then add the entire contents of the hardener to the base and mix by using a slow speed handheld powered mixer and mixing paddle for approximately two to three minutes to achieve a consistent mixture. Note: Do not use a separate mixing bucket as it may affect the mixing ratio.
Apply the whole mixed paint by using spreading rake, roller and brush to achieve the maximum coverage within the specified pot life time frame.
Do not add solvent to this product.
Slip resistance can be improved by lightly broadcasting anti-slip aggregates on the first coat (after primer) whilst still wet and back rolling, at a rate of 50/100 g/m2. When cured apply the second Resutile coat to secure the aggregates.
Full product data sheets and safety data sheets are available on request.
Product: Resutile
Finish: Gloss
Recommended thickness range: 100-150 μm WFT per coat
Colour: Available in a range of colours, please consult our technical sales team.
Preparation
Products required for this system
Primer : Resuseal WB Clear or Resuprime MVT on damp substrates where required
System: 1 or 2 Coats of Resutile
(Multiple coats will be required to achieve full coverage on low opacity colours such as bright yellows and reds)
APPLICATION INFORMATION at 20oC
Revised 09/2019—Issue 2 : REF : TIFL 2016 11
System Thickness
(Recommended)
100-150 microns WFT 56-84 microns DFT
*The suggested thickness range is calculated based on average volume solid as a general recommendation for the specified condition and for each application it may vary.
Solids Content by Weight 74% It may vary slightly for different colours
Pack Sizes 5 litres
Pack Make Up 1 x Base 1 x Hardener
Shelf Life 24 months (Base) 12 months (Hardener)
Storage Keep out of direct sunlight. Store in a dry place, between 15°C- 30°C.
Coverage Rate
(Theoretical)
5 litres will cover 50m2
@ 100 microns wet thickness.
* Coverage rate is calculated based on a sealed and smooth surface and may vary based on the substrate roughness and other conditions.
Pot Life 40 minutes
Recoating Intervals 6 hours or once surface has lost tackiness
Light Traffic 24 hours
Full Traffic 72 hours
Full Chemical Cure 7 days
Category Guide
FeRFA Category : 1 and 2
Technical Information
The following figures are obtained from laboratory tests and our experience with this product.
Slip Resistance Dry > 60
Method BS7976 pt1-3 2002
The slip resistance of a floor surface can vary as a result of the installation process, conditions at the time of application and subsequent traffic. Inappropriate cleaning or maintenance can adversely affect performance. For further advice on potential wet areas please consult our technical sales team.
Abrasion Resistance Average loss per 1000 cycles
79 micrograms Method BS8204 /ASTM D4060
Temperature Resistance Tolerant of temperatures of up to 150oC
Chemical Resistance Excellent chemical Resistance
Consult Sherwin-Williams on specific materials
Water Vapour Permeation
ASTM E96-80
Average permeability value
2.38 x 10-3g/mm/h/m2
/mm Hg
Linear Coefficient of Thermal
Expansion 15-30°c
(Extension rod dilatometry method)
7.5 x 10-50
C
Adhesion
BS3900 Part E 10
233 psi
Impact Resistance
BS 3900 Part E 7
Average result
154 micrometres
VOC 440 g/l calculated per full mixed unit
Transform any local tennis club lawn to a Wimbledon-worthy professional court with our top tips and tricks.
Proper preparation of your field or turf will ensure precise and vibrant lines that will stand the test of time.
Sports line marking can be daunting, with specific dimensions that directly shape the playing style and inform the rules, getting
The worst-case scenario is to spend a small fortune on line marking paint and applicators just for the fresh